GV180TI GEN-PACK (210kws/hour)
POWER RATING
| Model | Engine Speed rev/min | Type of Operation | Engine Power | |
|---|---|---|---|---|
| kWm | Ps | |||
|
GV180TIS
|
1800
|
Prime Power Standby Power |
340 375 |
462 510 |
|
GV180TIF
|
1500
|
Prime Power Standby Power |
290 319 |
394 434 |
Note
- The engine performance corresponds to ISO 3046, BS 5514 and DIN 6271.
* Without cooling fan, inter cooler inlet water temperature 32℃ - Ratings are based on ISO 8528.
- → Prime power available at variable load. The permissible average power out put (during 24h period) shell not exceed 70% of the prime power rating. No overload is permitted.
- → Standby power available in the event of a main power network failure. No overload is permitted.
|
Engine Type |
V-type 4 cycle, water cooled Turbo charged & intercooled (water to air) |
| Combustion type | Stoichiometric, Premixed and spark ignited |
| Cylinder Type | Replaceable wet liner |
| Number of cylinders | 10 |
| Bore x stroke | 128(5.04) x 142(5.59) mm(in.) |
| Displacement | 18.273 (1,115.09) lit.(in3) |
| Compression ratio | 10.5 : 1 |
| Firing order | 1-6-5-10-2-7-3-8-4-9 |
| Ignition timing | 14° BTDC |
| Compression pressure | Above 28 kg/cm2(398 psi) at 200rpm |
| Dry weight | Approx. 1,415 kg (3,120 lb) |
| Dimension (LxWxH) |
1,745 x 1,236 x 1,596 mm (68.7 x 48.7 x 62.8 in.) |
| Rotation | Counter clockwise viewed from Flywheel |
| Fly wheel housing | SAE NO.1 |
| Fly wheel | Clutch NO.14 |
| Type | Over head valve |
| Number of valve | Intake 1, exhaust 1 per cylinder |
| Valve lashes at cold | Intake 0.3mm (0.0118 in.) Exhaust 0.4mm (0.0157 in.) |
| Opening | Close | |
| Intake valve | 24 deg. BTDC | 36 deg. ABDC |
| Exhaust valve | 63 deg. BBDC | 27 deg. ATDC |
| Cooling method | Fresh water forced circulation |
| Water capacity | 42 liters ( 11.1 gal.) (Engine only) |
| Pressure system | Max. 0.5 kg/cm2 ( 7.1 psi) |
| Water pump | Centrifugal type driven by belt |
| Cooling fan | Blower, 915mm diameter, 7 blades Plastic |
| Loss power of fan | 28PS (18.5kW) @ Eng. Speed 1,500 rpm 33PS (24.3kW) @ Eng. Speed 1,800 rpm |
|
Thermostat |
Wax – pellet type Opening temp. 71°C Full open temp. 85°C |
| Charging generator | 24V x 45A alternator |
| Voltage regulator | Built-in type IC regulator |
| Starting motor | 24V x 7.0kW |
| Battery Voltage | 24V |
| Battery Capacity | 200 AH (recommended) |
| Ignition controller | 12 or 24V DC (min 8V DC at start, 32V DC max) |
|
Spark plug
|
NGK IFR7B-D, 0.4mm air gap Champion RC78PYP, 0.38mm air gap |
| Ignition controller | Altronic CPU-95 unit (24V DC) |
| Ignition coil | Altronic 501 061 blue epoxy individual coil |
| Trigger system | Magnetic pick-up sensor and trigger wheel and Hall-effect (0.5/ 0.5/ 1.0mm air gap) |
| Prime (Nm3/hr) | 1,500 rpm | 1,800 rpm |
|---|---|---|
| 25% | 26.1 | 31.9 |
| 50% | 41.5 | 50.6 |
| 75% | 57.4 | 71.7 |
| 90% | 67.5 | 83.4 |
| 100% | 74.7 | 90.8 |
| Standby (Nm3/hr) | 1,500 rpm | 1,800 rpm |
|---|---|---|
| 100% | 80.5 | 99.5 |
| Carburetor | Impco 200M Varifuel carburetor (2EA) |
| Gas regulator | Maxitrol RV61 (2EA) |
| Max. inlet pressure | 1.0 psi at the engine inlet |
| Lub. Method | Fully forced pressure feed type |
| Oil pump | Gear type driven by crankshaft |
| Oil filter | Full flow, cartridge type |
| Oil pan capacity | High level 35 liters ( 9.25 gal.) Low level 28 liters ( 7.40 gal.) |
| Lub. Oil | Refer to Operation Manual Low ash type(0.5wt%) natural gas engine oil API service grade CD or higher SAE 15W-40 |
| Water flow | 550 liters/min @1,500 rpm 660 liters/min @1,800 rpm |
| Heat rejection to coolant | 70.7 kcal/sec @1,500 rpm 87.3 kcal/sec @1,800 rpm |
| Heat rejection to CAC |
4.3 kcal/sec @1,500 rpm |
| Intercooler water flow | 290 liters/min @1,500 rpm 340 liters/min @1,800 rpm |
| Air flow | 23.9 m3/min @1,500 rpm 29.4 m3/min @1,800 rpm |
| Exhaust gas flow | 38.8 m3/min @1,500 rpm 47.9 m3/min @1,800 rpm |
| Exhaust gas temp. | 520 °C @1,500 rpm 530 °C @1,800 rpm |
| Radiator air flow | 550 m3/min @1,500 rpm, 0.7kPa 650 m3/min @1,800 rpm, 1.0kPa |
| Max. permissible restrictions | |
| Intake system | 220 mmH2O initial 635 mmH2O final |
| Exhaust system | 600 mmH2O max. |
| Altitude Capability | 1,000 m |
| in. = mm x 0.0394 | lb/ft = N.m x 0.737 |
| PS = kW x 1.3596 | U.S. gal = lit. x 0.264 |
| psi = kg/cm2 x 14.2233 | kW = 0.2388 kcal/s |
| in3 = lit. x 61.02 | lb/PS.h = g/kW.h x 0.00162 |
| hp = PS x 0.98635 | cfm = m3/min x 35.336 |
| lb = kg x 2.20462 | Nm3= SCF ×0.0283 |
| Kg/hr = Nm3/hr × 0.732 (natural gas) | |
| Btu/ft3= MJ/m3 × 26.8392 (natural gas) | |
| kPa = 101.97 mmH2O = 0.01 bar |
OTHER OUR PRODUCTS
GV222TI GEN-PACK (260kws/hour)
- Model :
- GV222TI GEN-PACK (260kws/hour)
GV180TI GEN-PACK (210kws/hour)
- Model :
- GV180TI GEN-PACK (210kws/hour)
ECU for Biogas Generator
- Model :
GE12TI GEN-PACK (110kws/hour)
- Model :
- GE12TI GEN-PACK (110kws/hour)
83/4 Suwinthawong Rd.,
Tel. : 
Email. : 
